一つの試験だけでは多くの時間を無駄にする必要がありません。640-875認定試験が大変難しいと感じて、多くの時間を取らなければならないとしたら、ツールとしてJPexamの640-875問題集を利用したほうがいいです。この問題集はあなたに時間を節約させることができますから。もっと重要なのは、この問題集はあなたが試験に合格することを保証できますから。この問題集よりもっと良いツールは何一つありません。試験の準備をするのにたくさんの時間を無駄にするより、そんな時間を利用してもっと有意義なことをしたほうがいいです。ですから、はやくJPexamのサイトに行ってもっと多くの情報を読みましょう。この素晴らしきチャンスを逃したらきっと後悔しますよ。
JPexamのCiscoの640-875試験トレーニング資料は現在で一番人気があるダウンロードのフォーマットを提供します。PDFとソフトのフォーマットで、ダウンロードするのは易いです。JPexamが提供した製品がIT専門家は実際の経験を活かして作った最も良い製品で、あなたが自分の目標を達成するようにずっと一生懸命頑張っています。
人生のチャンスを掴むことができる人は殆ど成功している人です。ですから、ぜひJPexamというチャンスを掴んでください。JPexamのCiscoの640-875試験トレーニング資料はあなたがCiscoの640-875認定試験に合格することを助けます。この認証を持っていたら、あなたは自分の夢を実現できます。そうすると人生には意義があります。
JPexam のCiscoの640-875問題集は１００パーセント検証とテストを通過したもので、認定試験に合格する専門的な指導者です。JPexam のCiscoの640-875練習問題集と解答は実践の検査に合格したソフトウェアで、最も受験生に合うトレーニングツールです。 JPexamで、あなたは一番良い準備資料を見つけられます。その資料は練習問題と解答に含まれています。弊社の資料があなたに練習を実践に移すチャンスを差し上げ、あなたはぜひCiscoの640-875試験に合格して自分の目標を達成できます。
「私はだめです。」という話を永遠に言わないでください。これは皆さんのためのアドバイスです。難しいCiscoの640-875認定試験に合格する能力を持たないと思っても、あなたは効率的な骨の折れないトレーニングツールを選んで試験に合格させることができます。JPexamのCiscoの640-875試験トレーニング資料はとても良いトレーニングツールで、１００パーセントの合格率を保証します。それに、資料の値段は手頃です。JPexamを利用したらあなたはきっと大いに利益を得ることができます。ですから、「私はだめです。」という話を言わないでください。諦めないのなら、希望が現れています。あなたの希望はJPexamのCiscoの640-875試験トレーニング資料にありますから、速く掴みましょう。
試験番号：640-875問題集
試験科目：Building Cisco Service Provider Next-Generation Networks, Part 1
最近更新時間：2014-02-16
問題と解答：全105問
100％の返金保証。1年間の無料アップデート。
JPexamは長い歴史を持っているCiscoの640-875トレーニング資料が提供されるサイトです。IT領域で長い時間に存在していますから、現在のよく知られていて、知名度が高い状況になりました。これは受験生の皆様を助けた結果です。JPexamが提供したCiscoの640-875トレーニング資料は問題と解答に含まれていて、IT技術専門家たちによって開発されたものです。Ciscoの640-875認定試験を受けたいのなら、JPexamを選ぶのは疑いないことです。
どんな業界で自分に良い昇進機会があると希望する職人がとても多いと思って、IT業界にも例外ではありません。ITの専門者はCiscoの640-875認定試験があなたの願望を助けって実現できるのがよく分かります。JPexamはあなたの夢に実現させるサイトでございます。
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.jpexam.com/640-875_exam.html
NO.1 Refer to the exhibit.
Company 1 has merged with Company 2. Company 1 is using RIPv2 as its IGP and Company 2 is using
EIGRP as its IGP. EIGRP also is running between R1 and R2 over the WAN link.
Which action must be taken to allow these two configurations?
The Company 1 RIP routes appear as external EIGRP routes within Company 2.
The Company 2 EIGRP routes appear as RIPv2 routes within Company 1.
A. Enable RIPv2 on the R2 router.
B. Enable RIPv2 on the R2 router and on all internal routers of Company 2. Enable EIGRP on all internal
routers of Company 1.
C. Configure mutual route redistribution between RIPv2 and EIGRP on the R1 and R2 routers.
D. Configure mutual route redistribution between RIPv2 and EIGRP on the R1 router.
E. Configure mutual route redistribution between RIPv2 and EIGRP on the R2 router.
Answer: D
Cisco 640-875 640-875問題集
NO.2 Given the IP address of 209.168.200.155/27, which two options are the subnet that this IP address
belongs to and the subnet broadcast IP address? (Choose two.)
A. 209.168.200.64 255.255.255.224
B. 209.168.200.96 255.255.255.224
C. 209.168.200.128 255.255.255.224
D. 209.168.200.95
E. 209.168.200.127
F. 209.168.200.159
Answer: CF
Cisco認証試験 640-875 640-875 640-875認定資格
NO.3 Which Cisco IOS CLI command is used to verify the speed and duplex settings on the Fa0/1 port on a
Cisco switch?
A. show ip interfaces fa0/1
B. show interfaces fa0/1
C. show interfaces fa0/1 switchport
D. show ip interfaces brief
E. show interfaces switchport
Answer: B
Cisco過去問 640-875問題集 640-875 640-875問題集 640-875
NO.4 Which statement about IPv6 global unicast addresses is true.?
A. The first 3 bits is 001.
B. The first 4 bits is 0011.
C. The first 4 bits is 1111.
D. The first 16 bits is FE80 in hex.
E. The first 16 bits is FF00 in hex.
F. The first 16 bits is 2002 in hex.
G. The first 16 bits is 3FFE in hex.
Answer: A
Cisco参考書 640-875 640-875認定試験 640-875
NO.5 Given the IP address 10.106.170.145 255.248.0.0, which three options are the subnet that this IP
address belongs to, the host IP address range on this subnet, and the subnet broadcast IP
address?(Choose three.)
A. subnet = 10.104.0.0/13
B. subnet = 10.106.0.0/13
C. subnet = 10.112.0.0/13
D. host IP address range = 10.104.0.1 to 10.111.255.254
E. host IP address range = 10.106.0.1 to 10.106.255.254
F. host IP address range = 10.106.0.1 to 10.119.255.254
G. subnet broadcast IP address = 10.106.255.255
H. subnet broadcast IP address = 10.111.255.255
I. subnet broadcast IP address = 10.119.255.255
Answer: ADH
Cisco 640-875過去問 640-875認証試験
NO.6 You are having problems browsing to http://www.cisco.com from your laptop that is running Windows.
Your laptop is connected directly to a default gateway, which is a Cisco ISR G2 router. Which four options
are the basic troubleshooting steps that you should use to troubleshoot this issue? (Choose four.)
A. Issue the ipconfig command from the Windows command line on your laptop to determine your laptop
IP address and the default gateway IP address.
B. Issue the ipconfig /all command from the Windows command line on your laptop to determine the DNS
server IP address.
C. Issue the ping {default gateway IP address} command from the Windows command line on your laptop
to verify connectivity to the default gateway.
D. Issue the ping {DNS server IP address} command from the Windows command line on your laptop to
verify connectivity to the DNS server.
E. Issue the ping tcp www.cisco.com 80 command from the Windows command line on your laptop to
verify TCP port 80 connectivity to the www.cisco.com server.
F. From the ISR G2 CLI, issue the ping tcp www.cisco.com 80 command to verify TCP port 80 connectivity
to the www.cisco.com server.
G. From the ISR G2 CLI, issue the ISR-G2#tracert www.cisco.com command to verify connectivity to the
www.cisco.com server.
H. From the ISR G2 CLI, issue the ISR-G2#nslookup www.cisco.com command to determine the IP
address of the www.cisco.com server.
Answer: ABCD
Cisco 640-875認定証 640-875認定試験 640-875
NO.7 When EIGRP is enabled on Cisco IOS XR, which EIGRP feature is on by default?
A. no auto-summary
B. stub routing
C. unequal cost paths load-balancing
D. no ip eigrp split-horizon
E. eigrp authentication
Answer: A
Cisco過去問 640-875 640-875問題集 640-875認証試験
NO.8 Refer to the exhibit.
Given the Class C IP network of 192.168.1.0, using VLSM, which five subnets meet the requirements in
the exhibit? (Choose five.)
A. 192.168.1.0/27
B. 192.168.1.32/27
C. 192.168.1.48/27
D. 192.168.1.48/28
E. 192.168.1.64/28
F. 192.168.1.80/28
G. 192.168.1.80/29
H. 192.168.1.88/30
I. 192.168.1.96/30
Answer: ABEFI
Cisco 640-875認定試験 640-875
NO.9 If a bridge port is in the non-designated state, which two statements about spanning-tree operations on
this port are true? (Choose two.)
A. This port is in the Forwarding state.
B. This port sends BPDUs on the attached link.
C. This port has the lowest cost to the root bridge.
D. This port is considered the root port.
E. This port receives BPDUs.
F. This port is in the Blocked state.
Answer: EF
Cisco 640-875認定試験 640-875 640-875
NO.10 This show output is from the S7 Cisco Metro Switch and the PE7 Cisco ASR 9000 Series Router. Which
configuration change(s) is/are needed to bring the S7 FastEthernet 0/2 interface into the up/up state?
S7#show cdp neighbors
<OUTPUT OMITTED>
*Mar 20 21:28:02.177: %ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD:
Collisions at FastEthernet0/2 exceed threshold. Considered as loop-back.
*Mar 20 21:28:02.177: %PM-4-ERR_DISABLE: loopback error detected on Fa0/2, putting Fa0/2 in
err-disable state
*Mar 20 21:28:03.184: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed
state to down
S7#show interface fa0/2
FastEthernet0/2 is down, line protocol is down (err-disabled)
Hardware is Fast Ethernet, address is e8ba.70b5.6c04 (bia e8ba.70b5.6c04)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:40, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
484423 packets input, 39349929 bytes, 0 no buffer
Received 484423 broadcasts (167203 multicasts)
0 runts, 0 giants, 0 throttles
1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 167203 multicast, 0 pause input
0 input packets with dribble condition detected
972398 packets output, 128931949 bytes, 0 underruns
0 output errors, 46 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
RP/0/RSP0/CPU0:PE7#show interfaces gi0/0/0/0
GigabitEthernet0/0/0/0 is down, line protocol is down
Interface state transitions: 4
Hardware is GigabitEthernet, address is 4055.392f.40a8 (bia 4055.392f.40a8)
Internet address is 192.168.107.70/24
MTU 1514 bytes, BW 100000 Kbit (Max: 100000 Kbit)
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation ARPA,
Full-duplex, 100Mb/s, THD, link type is force-up
output flow control is off, input flow control is off
loopback not set,
ARP type ARPA, ARP timeout 04:00:00
Last input 00:00:00, output 00:00:35
Last clearing of "show interface" counters never
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
972551 packets input, 128953765 bytes, 729 total input drops
172486 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 800781 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
484545 packets output, 39360900 bytes, 0 total output drops
Output 317283 broadcast packets, 167262 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
4 carrier transitions
A. Enable loopback line on the S7 Fa0/2 interface then shut and no shut the Fa0/2 interface.
B. Enable duplex half on the PE7 Gi0/0/0/0 interface then shut and no shut the Fa0/2 interface on S7.
C. Change S7 Fa0/2 interface to duplex full and speed 100 then shut and no shut the Fa0/2 interface.
D. Just need to no shut the Fa0/2 interface on S7.
E. Just need to shut and no shut the Fa0/2 interface on S7.
Answer: C
Cisco 640-875 640-875認定試験 640-875認証試験 640-875 640-875練習問題
NO.11 With IPv6, for which purpose are router solicitation and router advertisement used?
A. routing protocol updates
B. routing protocol neighbor peerings
C. router and prefix discovery
D. Layer 3 to Layer 2 address resolution (similar to IPv4 ARP)
Answer: C
Cisco 640-875 640-875 640-875 640-875練習問題
NO.12 Which three physical lines can provide local or remote access to a Cisco router or switch? (Choose
three.)
A. console port
B. modem port
C. virtual terminal lines
D. switch fabric interface
E. aux port
F. managementEthernet0/RSP0/CPU0/0
Answer: AEF
Cisco 640-875 640-875認定試験
NO.13 Which two statements about classful or classless routing protocol operations are true? (Choose two.)
A. Classful routing protocols do not send subnet mask information with their routing updates
B. Variable-length subnet masks are supported when using classful routing protocols.
C. Examples of classless routing protocols include RIPv1, EIGRP, OSPF, and IS-IS.
D. Classful routing protocols do not support discontiguous subnets.
Answer: AD
Cisco 640-875 640-875参考書 640-875
NO.14 Which two statements about IPv4 DHCP operations are true? (Choose two.)
A. If the DHCP clients and servers are on the same subnet, DHCP uses UDP broadcasts to communicate
between the clients and servers.
B. The DHCP server that receives a DHCPDISCOVER message may respond with a DHCPOFFER
message on UDP port 67.
C. A client can receive DHCPOFFER from multiple servers and it can accept all the offers by broadcasting
the DHCPREQUEST message to all the servers.
D. A DHCP relay is required if the DHCP clients and the servers are on the same subnet.
E. If the client and server are on different subnets, DHCPDISCOVER and DHCPREQUEST messages
are sent via UDP broadcasts, but DHCPOFFER and DHCPACK messages are unicast.
F. The client broadcasts a DHCPDISCOVER message on UDP port 68 with its own MAC address to
discover available DHCP servers.
Answer: AE
Cisco参考書 640-875認定証 640-875 640-875
NO.15 Which three statements about the ARP function are true? (Choose three.)
A. ARP is used to determine an IP address.
B. An ARP request is broadcast at Layer 3.
C. An ARP response is broadcast at Layer 2.
D. ARP tables are maintained on Layer 3 devices.
E. The destination MAC address of an ARP request is that of the ARP responder.
F. ARP requests are broadcast at Layer 2.
G. ARP resolves MAC addresses to NET addresses.
H. ARP uses 0x0806 as the Type field in an Ethernet frame.
Answer: DFH
Cisco 640-875参考書 640-875認証試験
JPexamは最新の650-304問題集と高品質の70-463問題と回答を提供します。JPexamの70-485 VCEテストエンジンとC_TSCM42_65試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質のC-TSCM62-65 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。
没有评论:
发表评论